ProSoft Technology ProLinx-HART Specifikace stáhnout pdf (Strana 79)

Reference HART ♦ ProLinx Gateway

Driver Manual HART Master

ProSoft Technology, Inc. Page 79 of 119

July 7, 2009

COMMAND 48 - Read Additional Transmitter Status

Description

This command gets extended information about the status of the Transmitter.

This information is specific for each transmitter.

Write Parameters

NONE

Floating Point Data Returned

NONE

Integer Data Returned

Word High Byte Low Byte

0 STATUS WORD

1 Additional Status (Byte 0) Additional Status (Byte 1)

2 Additional Status (Byte 2) Additional Status (Byte 3)

13 Additional Status (Byte 24) 0

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 118 119

DRIVER MANUAL 1
All ProLinx® Products 2
Your Feedback Please 3
Contents 5
1 Start Here 7
1.2 Package Contents 8
1.5.1 Using the Help System 10
2 Functional Overview 11
Port Label Function 12
Channel 6 Hart Port 5 12
Channel 7 Hart Port 6 12
Channel 8 HART Port 7 12
2.3.2 Auto-Polling 15
2.3.3 HART Command List 23
3 Configure the Gateway 25
EFAULT PROJECT and 26
3.1 Module Entries 27
3.3 [HART PORT x] 28
3.3.1 Enabled 28
3.3.2 Preambles 29
3.3.3 Primary Master 29
3.3.4 Retry Count 29
3.3.5 DB Address Status 29
3.3.6 Command Count 29
3.3.7 Auto-Poll Code 30
3.3.8 Auto-Poll DB Address 30
3.3.9 Auto-Poll Swap Float 30
3.3.10 Max Device Count 30
3.4 [HART PORT x COMMANDS] 31
3.4.1 Command List Overview 31
3.4.3 Enable 32
3.4.4 Float DB Address 33
3.4.5 Poll Interval 33
3.4.6 FP Word Count 33
3.4.7 Swap Code 33
3.4.8 Short Address 34
3.4.9 Function Code 34
3.4.10 Int. DB Address 36
3.4.11 Int Word Count 36
3.4.12 Swap Code 37
3.4.13 Use Long 37
3.4.14 Enable DB Address 37
3.4.15 Done DB Address 37
3.4.16 Write DB Address 37
3.4.17 Swap Code 38
3.4.18 Byte Count 38
3.4.19 Fixed Data 38
3.5 Data Map 39
3.5.2 From Address 40
3.5.3 To Address 40
3.5.4 Register Count 40
3.5.5 Swap Code 40
3.5.6 Delay Preset 41
OWNLOAD dialog box opens 42
OWNLOAD button 42
4 Error/Status Data 43
4.6.2 Slave List Status 47
4.7 Module Error Codes 47
4.7.1 Protocol Error Codes 47
5 Reference 51
Word High Byte Low Byte 55
0 STATUS WORD 55
1 Polling Address 0 55
COMMAND 12 - Read Message 56
COMMAND 17 - Write Message 61
COMMAND 39 - EEPROM Control 70
COMMAND 43 - Set PV Zero 74
COMMAND 44 - Write PV Units 75
COMMAND 45 - Trim DAC Zero 76
COMMAND 46 - Trim DAC Gain 77
1 Transfer Function Code 0 78
Type Network Power Supply 94
A Required 94
B Required 94
C Must not be used 94
5.4 HART Status Data Map 102
5.4.2 Port 0 Command Errors 102
5.4.4 Port 1 Command Errors 103
5.4.5 Port 2 Data 103
5.4.9 Port 6 Data 104
5.4.10 Port 7 Data 104
5.4.6 Port 3 Data 104
5.4.7 Port 4 Data 104
5.4.8 Port 5 Data 104
5.5 Module Status Values 105
5.5.1 Normal Operation 105
5.5.2 Interface Crash Codes 105
5.5.3 Fatal Crash Codes 105
5.5.4 Peer Status Codes 106
5.6 Module Status Data Map 107
5.6.2 HTTP Port 80 Status 107
5.6.3 SNTP Client Status 107
In This Chapter 111
6.2.1 All Product Returns: 112
6.3 LIMITED WARRANTY 113
6.3.8 No Other Warranties 116
6.3.9 Allocation of Risks 116
Write DB Address • 37 119
Your Feedback Please • 3 119

Komentáře k této Příručce

Žádné komentáře

ProSoft Technology ProLinx-HART Specifikace Strana 79

Komentáře k této Příručce

Související produkty a manuály pro Brány / ovladače ProSoft Technology ProLinx-HART